Home»House Plants»Ficus
There are several reasonableness why a Rubber Plant might drop its leave . However , the most vernacular causa are underwatering and overwatering .
When you see that your plant has droopy leaves , the first matter you should do is check the soil .
allow it dry out out almost entirely if it ’s quaggy before water again . If it ’s dry , give the industrial plant a honest , cryptical watering .
Avoid over watering or underwatering in the hereafter by using the soak and dry method of watering .
Monitor your plant life ’ grime and only water when the top couple of inches are ironic .
Then , water system thoroughly with condense , filter , or rainfall water supply . or so once a calendar week is a good schedule , but you ’ll need to keep tab on your plant in your mount to find out what watering schedule will work for you .
11 Causes & Solutions For Droopy Rubber Plant Leaves:
If your drooping Rubber Plant leaves are not make by wrong lacrimation , there may be another cause .
Here are some of the top reasonableness and treatments for drooping foliage on Rubber Plants .
1. Poor Communication
If you are not the only someone watering your plant , you run a risk droopy leaf due to planetary watering . Establish and post a docket .
2. Hunger
Rubber Trees like a light monthly alimentation with a half - strength houseplant fertilizer throughout the spring and summer growing season .
Be careful not to exaggerate it because too much fertilizer can damage the roots , thus make droopy leaves .
Just total a half dose of melted fertiliser to the plant ’s water once a calendar month . Do n’t fertilize at all in the autumn and the winter .
3. Wrong Light
Rubber Tree plants of course grow in tropical rainforests where they receive lots of separate out sunlight . This translates to a bright indirect sunlight set in your home .
Your plant should not model right next to a window where it gets coarse , direct visible light . It also should not sit in a dour area of your dwelling house .
Place it in an area that gets about six hours a day of natural light that does not shine directly on its leaves . Supplement with contrived lighting as needed .
4. Cold
Temperatures below 50 ° degrees Fahrenheit will cause your Rubber Plant ’s leaves to droop .
Therefore , keep your flora at temperatures between 60 ° and 75 ° degrees Fahrenheit .
Be aware that the room ’s ambient temperature may be warm than the temperature of the grime in your plant ’s container if the works is sitting on a cold trading floor .
Likewise , the air around the flora may be cool than the air in the elbow room if the plant is sitting near a window or a room access .
For these reasons , it ’s wise to go down your plant on a stand in an area that is protected from cold-blooded drafts or cold seeping in through or around windows .
In addition , keep a thermometer very near the flora to keep close-fitting tabs on its temperature .
5. Sudden Changes
The temperature rising and falling all of a sudden and unpredictably can get drooping Rubber Tree plant life leave .
In addition , flack of heat energy or cold are damaging , so keep your plant life out of selective service in winter and summer .
The industrial plant should not sit near a threshold or in front of a heater or melodic line conditioner .
The skilful setting for Rubber Tree plants ( and plant in cosmopolitan ) is one that cater consistently fond temperatures and lightly moving air .
6. Dry Air
Tropical Rubber Tree plant need high humidness ( 40 % to 50 % pct ) .
If your plant ’s territory has dried out because of dry air travel ( e.g. , centrally heated indoor zephyr in winter ) , move the plant to an area away from the high temperature germ and give it a rich watering .
Keep the air besiege your Rubber Tree humidified adequately through a humidifier or a pebble tray . obnubilate the leaves and wipe them with a clean-living , damp cloth every week .
7. Wet Air
Be cognizant that excessive humidity can also stimulate sagging leaves .
Set a small fan in the corner of the room ( face into the corner ) and keep it endure on a low setting just to keep the melodic phrase in the way moving a bit .
This will facilitate prevent fungal development that is sometimes cause by gamy humidity .
8. Compacted Soil
If you have been overwatering , the flora ’s grease may not be allowing enough oxygen to get to the source even after it has dry out a bite .
In this cause , you ’ll need to repot your industrial plant into all smart , light , airy , well - run out potting soil .
Be careful not to apply a can that is too giving because this can often do you to give the plant more water than it needs as you set about to drench the soil .
9. Crowding
If it has been a long fourth dimension since you last repotted your plant ( or if you have never repotted it ) , the problem may be a deficiency of gentle wind circulation to the etymon and lack of nutrients because the industrial plant roots have consumed all the nutrients in the soil and displaced the land .
Check to see if the DoI of your plant ’s container is full of root with very minuscule grease .
If this is the case , you ’ll want to repot . But , again , be heedful not to over - pot . Just go up to the next size of it .
When you repot a mess - bound plant , do the following :
10. Shock
After you repot your Rubber Tree , it may get droopy leaves due to graft shock .
It may also lose a few leaves . Do n’t worry too much about this .
Just place your plant in an area that provides consistent warmth and humidity and bright , collateral sunlight , and gentle airwave circulation .
Be patient . Your plant will razz and thrive in good fourth dimension .
observe that Rubber Trees late relocated ( even without repotting ) may also suffer shock .
But , again , just be patient and provide consistent concern , and your plant life will pull through .
11. Pests
Incorrect attention will make your plant life susceptible to houseplant blighter , such as :
A heavy plague will cause droopy leaves , but the good news is that you could keep off plague completely by following the tips given above and providing your plant life with right care .
Examine your plant ’s foliage ( top and bottom ) frequently .
The import you see any signs of pest infestation , do the undermentioned steps :
This also helps keep the leaves clean , intelligent , and a bit glistening .
